C1 (1953-1962)
Showing all 16 results
-
![]()
MORE INFO’56-’57 Hood
$1,200.00Eliminated factory latches and made inside uniform for a clean look.
Removed bracing. Inner framework is all one piece.
Hood has a smooth finish on both sides, not to be confused with press molded. This hood will come with a class “A” finish on both sides with the hardware built into the hood for mounting.
Racer? Need the absolute lightest hood possible?? We can make this hood as just a hood skin for
Fiberglass – $600
Carbon Fiber- $1,200
Check out the Hood Skin product listing, and Carbon Fiber hood along with other hand picked recommendations for this product at the “You May Also Like…” section below!
-
![]()
MORE INFOCenter Console / Armrest – ’58-’62
$350.00This console was designed to make your life a little more comfortable in your C1 Corvette
Built to accommodate an original 58-62 or a Restomod
Test fitting is required and alterations will be required for a perfect fit. Console can be painted or covered as shown in the photo and will screw into place. Cup inserts are another great option for the console and can be found online or in boat stores in varies sizes and colors. Console can be painted or covered as shown.
Will Not Come Finished As Shown In Photo
Check Out “You May Also Like…” Section Below For Hand Picked Recommendations To Go With This Item
-
![]()
MORE INFOFirewall – ’58-’62
$350.00This firewall block off was designed with the 58-62 RestOmods in mind. It’s meant to slick out the firewall for a smooth finish in a fraction of time also allowing you the freedom to run wires and plumbing in other locations through the firewall. This cover should be bonded into place and will require a wiper motor delete.
Want More? Check out our C1 Engine Bay Block Off Kit In The “You May Also Like…” Section Below to completely slick out your engine compartment!
-
![]()
MORE INFOFirewall, Inner Fender Extensions, & Retainers -’58-’62
$900.00This part is meant to slick out the engine compartment for a smooth finish in a fraction of time also allowing you the freedom to run wires and plumbing in other locations through the firewall. The firewall cover will require a wiper motor delete.
Meant to slick out your engine compartment, this kit will accommodate any 58-62 Corvette chassis and engine, original or aftermarket
You will get a firewall cover, 2 upper & 2 lower retainers and 2 fender caps
To install the firewall you will need to sand down the original then bond ours into place. To install the fender caps and retainers you will fit your body to the chassis and scribe where the original fenders will need to be removed, you will then pre-fit our fender caps and retainers and cut to accommodate your chassis. The fender caps & retainers should be bonded into place and body worked to a smooth finish.
Test fitting every part is extremely important and if you have any questions please contact us prior to ordering
Don’t Need The Full Kit? Purchase Any Piece Individually!
Check Out The “You May Also Like…” Section Below For Those Products, Along With Other Hand Picked Recommendations To Go With This Item
-
![]()
MORE INFOHolley Sniper to Stock Air Cleaner Base – C1-C2-C3 Models
$125.00Compatible with Holley Sniper Part # 550-511, 550-510 and 550-516)
Use our air cleaner base with Holly Sniper to keep the original air cleaner.
Requires modification to fit your vehicle. Cut out to original airbase, Bond it, Bodywork our piece to your specs, Paint it.
Check out the “You May Also Like…” Section below for hand picked recommendations to go with this item.
-
![]()
MORE INFOHood – ’56-’57 – Carbon Fiber
$2,400.00Carbon Fiber parts have to be clear coated with a high ultra-violet blocking (UVB) clearcoat.
Carbon Fiber Outer Skin Only
Eliminated factory latches and made inside uniform for a clean look.
Removed bracing. Inner framework is all one piece.
Hood has a smooth finish on both sides, not to be confused with press molded. This hood will come with a class “A” finish on both sides with the hardware built into the hood for mounting.
Racer? Need the absolute lightest hood possible?? We can make this hood as just a hood skin for
Fiberglass – $600
Carbon Fiber- $1,200
Check out the Hood Skin product listing and Fiberglass version of this hood, along with other hand picked recommendations for this product at the “You May Also Like…” section below!
-
![]()
MORE INFOHood – ’59-’62
$1,200.00Also available in Carbon Fiber
Eliminated factory latches and made inside uniform for a clean look.
Removed bracing. Inner framework is all one piece.
This hood is designed for use with a linear actuator. This allows hood to be opened and closed with a motor. Requires linear actuators with bumper stops or hood pins.
Racer? Need the absolute lightest hood possible?? We can make this hood as just a hood skin for
Fiberglass – $600
Carbon Fiber- $1,200
Check out the Hood Skin product listing, and Carbon Fiber hood along with other hand picked recommendations for this product at the “You May Also Like…” section below!
-
![]()
MORE INFOHood – ’59-’62 – Carbon Fiber
$2,400.00Carbon Fiber parts have to be clear coated with a high ultra-violet blocking (UVB) clearcoat.
Carbon Fiber Outer Skin Only
Note: The pictures here are of our fiberglass version of this product. The dimensions are exactly the same whether you order fiberglass or carbon fiber.
Eliminated factory latches and made inside uniform for a clean look.
Removed bracing. Inner framework is all one piece.
This hood is designed for use with a linear actuator. This allows hood to be opened and closed with a motor. Requires linear actuators with bumper stops or hood pins.
Racer? Need the absolute lightest hood possible?? We can make this hood as just a hood skin for
Fiberglass – $600
Carbon Fiber- $1,200
Check out the Hood Skin product listing and Fiberglass version of this hood, along with other hand picked recommendations for this product at the “You May Also Like…” section below!
-
![]()
MORE INFOInner Fender Extensions (at suspension)
$450.00These extensions are made to cover where you cut back the original fenders to accommodate the suspension of an aftermarket chassis.
Want More? Check out our C1 Engine Bay Block Off Kit In The “You May Also Like…” Section Below to completely slick out your engine compartment!
-
![]()
MORE INFOInner Fender Retainers (4 Piece)
$125.00Bond in our retainers to give you a finished look inside the corners of the inner fenders to the firewall.
Want More? Check out our C1 Engine Bay Block Off Kit In The “You May Also Like…” Section Below to completely slick out your engine compartment!
-
![]()
MORE INFONose Panel – ’53-’62 (Used To Delete Front License Plate & Brackets)
$175.00Specifically designed with the custom RestOmod C1 Corvettes in mind, this lower nose panel was designed to fill the license plate bracket openings. This panel is easily bonded into place and body worked for a perfect smooth nose deleting the front license plate and brackets. With the bonding strips built into the part this will save you time on your build and give you an added custom look to your C1 RestOmod Corvette
Check Out The “You May Also Like…” Section Below For Hand Picked Recommendations To Go With This Item
-
![]()
MORE INFOTrunk Latch Bracket – Use When You Eliminate Spare Tire
$125.00With our custom trunk latch bracket you can build your C1 corvette without a spare tire and tub. Bond this bracket into place and body to a smooth finish to mount your trunk latch to so you won’t need the spare tire tub.
Check Out The “You May Also Like…” Section Below For Hand Picked Recommendations To Go With This Item
