56-’60 Door Skins
$1,100.00 – $2,200.00
Available in Fiberglass or Carbon Fiber
Carbon Fiber parts have to be clear coated with a high ultra-violet blocking (UVB) clearcoat.
Carbon Fiber Outer Skin Only
Keep scrolling down for more info. Scroll to the bottom of the page for general instruction videos.
Description
You may also like…
-
![]()
MORE INFOFirewall, Inner Fender Extensions, & Retainers -’58-’62
$1,100.00This part is meant to slick out the engine compartment for a smooth finish in a fraction of time also allowing you the freedom to run wires and plumbing in other locations through the firewall. The firewall cover will require a wiper motor delete.
Meant to slick out your engine compartment, this kit will accommodate any 58-62 Corvette chassis and engine, original or aftermarket
You will get a firewall cover, 2 upper & 2 lower retainers and 2 fender caps
To install the firewall you will need to sand down the original then bond ours into place. To install the fender caps and retainers you will fit your body to the chassis and scribe where the original fenders will need to be removed, you will then pre-fit our fender caps and retainers and cut to accommodate your chassis. The fender caps & retainers should be bonded into place and body worked to a smooth finish.
Test fitting every part is extremely important and if you have any questions please contact us prior to ordering
Don’t Need The Full Kit? Purchase Any Piece Individually!
Check Out The “You May Also Like…” Section Below For Those Products, Along With Other Hand Picked Recommendations To Go With This Item
-
![]()
MORE INFOTwo-Part Epoxy
$175.00Use what we use in our shop!
Material Safety Data Sheets Available Here:
Check out the “You May Also Like…” Section below for hand picked recommendations to go with this item.
Keep scrolling down for more info. Scroll to the bottom of the page for general instruction videos.
-
![]()
MORE INFONose Panel – ’58-’62 (Used To Delete Front License Plate & Brackets)
$200.00Specifically designed with the custom RestOmod C1 Corvettes in mind, this lower nose panel was designed to fill the license plate bracket openings. This panel is easily bonded into place and body worked for a perfect smooth nose deleting the front license plate and brackets. With the bonding strips built into the part this will save you time on your build and give you an added custom look to your C1 RestOmod Corvette
Check Out The “You May Also Like…” Section Below For Hand Picked Recommendations To Go With This Item
Keep scrolling down for more info. Scroll to the bottom of the page for general instruction videos.
-
![]()
MORE INFO56-’57 Hood
$1,450.00 – $2,900.00Available in Fiberglass C1-108 (First price shown above) or Carbon Fiber C1-112 (Second price shown above)
Note: Pictures or descriptions in this listing may describe or show the Fiberglass version of this product or the Carbon Fiber version. If you have any questions, please contact us!
Carbon Fiber parts have to be clear coated with a high ultra-violet blocking (UVB) clearcoat.
Carbon Fiber outer skin only
Eliminated factory latches and made inside uniform for a clean look.
Removed bracing. Inner framework is all one piece.
Hood has a smooth finish on both sides, not to be confused with press molded. This hood will come with a class “A” finish on both sides with the hardware built into the hood for mounting.
Racer? Need the absolute lightest hood possible?? We can make this hood as just a hood skin!
Check out the Hood Skin product listing, and Carbon Fiber hood along with other hand picked recommendations for this product at the “You May Also Like…” section below!
Keep scrolling down for more info. Scroll to the bottom of the page for general instruction videos.
Related products
-
![]()
MORE INFO58-’62 Headlight Buckets, Headlight Bezel and Fender Spears/ Top Fender Molding Kit – Fiberglass
$2,650.00Bezel and molding finished off and attach with mechanical fasteners on the back. No hardware on the outside.
Headlight bucket designed to work with Dapper headlights (aprox 1/1-2 in. deeper)
Available in Carbon Fiber, Fiberglass or Chrome Plated! (See recommended products below for links)
If you’re able and willing to install the hardware yourself a $400 discount is available (for fiberglass kit only).
Check Out The “You May Also Like…” Section Below For Hand Picked Recommendations To Go With This Item
Keep scrolling down for more info. Scroll to the bottom of the page for general instruction videos.
-
![]()
MORE INFO61-62 Trunk Lid
$1,800.00Class A Finish On Both Sides
Designed to work with ‘58-’62 Hood Bulk Weatherstrip
Check Out The “You May Also Like…” Section Below For Hand Picked Recommendations To Go With This Item
Keep scrolling down for more info. Scroll to the bottom of the page for general instruction videos.
-
![]()
MORE INFO58-62 Front Bumpers – Fiberglass
$1,300.00Available in Fiberglass, Carbon Fiber, or Chrome Plated!
Flush mount bumpers that tuck in tight.
Attaches with 5/16 mechanical fasteners that are glassed in on the back.
Note: These bumpers were tooled off a 58-60 bumper (with grill teeth). If using these bumpers on your ‘61-’62 the grill bar will be back aprox 5/8 in.
Check Out The “You May Also Like…” Section Below For Hand Picked Recommendations To Go With This Item
Keep scrolling down for more info. Scroll to the bottom of the page for general instruction videos.
-
![]()
MORE INFO58-’62 Eyebrows and Grill Molding Set – Fiberglass
$1,300.00Available in Fiberglass, Carbon Fiber, or Chrome Plated!
Please watch both videos below to see how the part is installed before ordering
Check Out The “You May Also Like…” Section Below For Hand Picked Recommendations To Go With This Item
Keep scrolling down for more info. Scroll to the bottom of the page for general instruction videos.
